Arduino audio tests using the Mozzi library, a Nano board, a light dependent resistor and a potentiometer (volume control).
http://sensorium.github.io/Mozzi/learn/introductory-tutorial/
The blog
Arduino audio tests using the Mozzi library, a Nano board, a light dependent resistor and a potentiometer (volume control).
http://sensorium.github.io/Mozzi/learn/introductory-tutorial/
Working through this tutorial currently, trying to understand how Processing can be used to network an Arduino and power the colour of a lamp from words featured in an XML feed (in this case my blog feed – replacing the word ‘love’ with ‘space’ and the word ‘peace’ with ‘rock’). This generates the colour #3C4C2C.

And after adding this post to the feed…
Note the slight colour change.
This is the circuit I used, from this website. The LED is a 4 pin one, which can generate any combination of RGB colour as light:

And the two versions of it that I built:


Here is the code used in Processing:
//Arduino Code for the Arduino Networked Lamp - Processing
#define SENSOR 0
#define R_LED 9
#define G_LED 10
#define B_LED 11
#define BUTTON 12
int val =0; //variable to store the value coming from the sensor
int btn = LOW;
int old_btn = LOW;
int state = 0;
char buffer[7];
int pointer = 0;
byte inByte = 0;
byte r = 0;
byte g = 0;
byte b = 0;
void setup() {
Serial.begin(9600); //open up serial port
pinMode(BUTTON, INPUT);
}
void loop() {
val = analogRead(SENSOR);
Serial.println(val);
if (Serial.available() >0) {
//read incoming byte
inByte = Serial.read();
if (inByte == '#') {
while (pointer < 6) {
buffer[pointer] = Serial.read();
pointer++;
}
//now need to decode 3 numbers of colors stored as hex numbers into 3 bytes
r = hex2dec(buffer[1]) +hex2dec(buffer[0])*16;
g = hex2dec(buffer[3]) +hex2dec(buffer[2])*16;
b = hex2dec(buffer[5]) +hex2dec(buffer[4])*16;
pointer = 0; //reset pointer
}
}
btn = digitalRead(BUTTON);
//check if there was a transition
if ((btn == HIGH) && (old_btn == LOW)) {
state = 1-state;
}
old_btn = btn; //val is now old,lets store it
if (state == 1) {
analogWrite(R_LED, r);
analogWrite(G_LED, g);
analogWrite(B_LED, b);
}
else {
analogWrite(R_LED, 0);
analogWrite(G_LED, 0);
analogWrite(B_LED, 0);
}
delay(100);
}
int hex2dec(byte c) {
if (c >= '0' && c<= '9') {
return c- '0';
} else if (c >='A' && c <= 'F') {
return c - 'A' + 10;
}
}
And the code in Arduino:
//Arduino Code for the Arduino Networked Lamp - Arduino
#define SENSOR 0
#define R_LED 9
#define G_LED 10
#define B_LED 11
#define BUTTON 12
int val =0; //variable to store the value coming from the sensor
int btn = LOW;
int old_btn = LOW;
int state = 0;
char buffer[7];
int pointer = 0;
byte inByte = 0;
byte r = 0;
byte g = 0;
byte b = 0;
void setup() {
Serial.begin(9600); //open up serial port
pinMode(BUTTON, INPUT);
}
void loop() {
val = analogRead(SENSOR);
Serial.println(val);
if (Serial.available() >0) {
//read incoming byte
inByte = Serial.read();
if (inByte == '#') {
while (pointer < 6) {
buffer[pointer] = Serial.read();
pointer++;
}
//now need to decode 3 numbers of colors stored as hex numbers into 3 bytes
r = hex2dec(buffer[1]) +hex2dec(buffer[0])*16;
g = hex2dec(buffer[3]) +hex2dec(buffer[2])*16;
b = hex2dec(buffer[5]) +hex2dec(buffer[4])*16;
pointer = 0; //reset pointer
}
}
btn = digitalRead(BUTTON);
//check if there was a transition
if ((btn == HIGH) && (old_btn == LOW)) {
state = 1-state;
}
old_btn = btn; //val is now old,lets store it
if (state == 1) {
analogWrite(R_LED, r);
analogWrite(G_LED, g);
analogWrite(B_LED, b);
}
else {
analogWrite(R_LED, 0);
analogWrite(G_LED, 0);
analogWrite(B_LED, 0);
}
delay(100);
}
int hex2dec(byte c) {
if (c >= '0' && c<= '9') {
return c- '0';
} else if (c >='A' && c <= 'F') {
return c - 'A' + 10;
}
}
This didn’t work the first time I ran it, so I had to specify the Arduino port that Processing should use and then…
Today I’ve been looking at how to build the various Arduino circuits for the Space Rocks, and at some examples of relevant projects.
I made some basic sensor experiments with a Light-dependent resistor, ultimately using this code from the Make: Getting Started with Arduino book.
// Example 06b: Blink LED at a rate specified by the
// value of the analogue input
# define LED 9 // the pin for the LED
int val = 0; // variable used to store the value
// coming from the sensor
void setup() {
// put your setup code here, to run once:
pinMode(LED, OUTPUT); // LED is as an output
// note Analogue pins are
// automatically set as inputs
}
void loop() {
// put your main code here, to run repeatedly:
val = analogRead(0); // read the value from the sensor
analogWrite(LED, val/4); // turn the LED on at
// the brightness set
// by the sensor
delay(10); // stop the program for some time
}
And this circuit:


Also stumbled upon How to Build an Arduino synthesizer with Mozzi library
The Mozzi library looks super-useful for sound generation:
Currently your Arduino can only beep like a microwave oven. Mozzi brings your Arduino to life by allowing it to produce much more complex and interesting growls, sweeps and chorusing atmospherics. These sounds can be quickly and easily constructed from familiar synthesis units like oscillators, delays, filters and envelopes.
You can use Mozzi to generate algorithmic music for an installation or performance, or make interactive sonifications of sensors, on a small, modular and super cheap Arduino, without the need for additional shields, message passing or external synths.
Note to self to also check out the Mozzi examples gallery.
The latest 3D printed prototypes for the Space Rock shapes.
Plus a video of the shells glowing, courtesy of Arduino.
Some low resolution 3D prints. Getting used to the process, investigating how to add the electronics for audio and interaction and also working out the most ergonomic size for the final objects. In this case, bigger is definitely better.
Finally at the stage where I can play a good quality sounding MP3 file through Arduino. It doesn’t sound so ‘good’ here as it is routed back through the laptop and Audacity via a crackly audio interface connection, but it is quite clear on headphones. And it’s now ready for me to start triggering these MP3 files via various sensors.
Here’s the code used:
//code rearranged by Javier Muñoz 10/11/2016 ask me at javimusama@hotmail.com
#include <SoftwareSerial.h>
#define ARDUINO_RX 5//should connect to TX of the Serial MP3 Player module
#define ARDUINO_TX 6//connect to RX of the module
SoftwareSerial mySerial(ARDUINO_RX, ARDUINO_TX);//init the serial protocol, tell to myserial wich pins are TX and RX
////////////////////////////////////////////////////////////////////////////////////
//all the commands needed in the datasheet(http://geekmatic.in.ua/pdf/Catalex_MP3_board.pdf)
static int8_t Send_buf[8] = {0} ;//The MP3 player undestands orders in a 8 int string
//0X7E FF 06 command 00 00 00 EF;(if command =01 next song order)
#define NEXT_SONG 0X01
#define PREV_SONG 0X02
#define CMD_PLAY_W_INDEX 0X03 //DATA IS REQUIRED (number of song)
#define VOLUME_UP_ONE 0X04
#define VOLUME_DOWN_ONE 0X05
#define CMD_SET_VOLUME 0X06//DATA IS REQUIRED (number of volume from 0 up to 30(0x1E))
#define SET_DAC 0X17
#define CMD_PLAY_WITHVOLUME 0X22 //data is needed 0x7E 06 22 00 xx yy EF;(xx volume)(yy number of song)
#define CMD_SEL_DEV 0X09 //SELECT STORAGE DEVICE, DATA IS REQUIRED
#define DEV_TF 0X02 //HELLO,IM THE DATA REQUIRED
#define SLEEP_MODE_START 0X0A
#define SLEEP_MODE_WAKEUP 0X0B
#define CMD_RESET 0X0C//CHIP RESET
#define CMD_PLAY 0X0D //RESUME PLAYBACK
#define CMD_PAUSE 0X0E //PLAYBACK IS PAUSED
#define CMD_PLAY_WITHFOLDER 0X0F//DATA IS NEEDED, 0x7E 06 0F 00 01 02 EF;(play the song with the directory \01\002xxxxxx.mp3
#define STOP_PLAY 0X16
#define PLAY_FOLDER 0X17// data is needed 0x7E 06 17 00 01 XX EF;(play the 01 folder)(value xx we dont care)
#define SET_CYCLEPLAY 0X19//data is needed 00 start; 01 close
#define SET_DAC 0X17//data is needed 00 start DAC OUTPUT;01 DAC no output
////////////////////////////////////////////////////////////////////////////////////
void setup()
{
Serial.begin(9600);//Start our Serial coms for serial monitor in our pc
mySerial.begin(9600);//Start our Serial coms for THE MP3
delay(500);//Wait chip initialization is complete
sendCommand(CMD_SEL_DEV, DEV_TF);//select the TF card
delay(200);//wait for 200ms
}
void loop()
{
sendCommand(CMD_PLAY_WITHVOLUME, 0X0F01);//play the first song with volume 15 class
delay(1000000);//the programm will send the play option each 100 seconds to the catalex chip
}
void sendCommand(int8_t command, int16_t dat)
{
delay(20);
Send_buf[0] = 0x7e; //starting byte
Send_buf[1] = 0xff; //version
Send_buf[2] = 0x06; //the number of bytes of the command without starting byte and ending byte
Send_buf[3] = command; //
Send_buf[4] = 0x00;//0x00 = no feedback, 0x01 = feedback
Send_buf[5] = (int8_t)(dat >> 8);//datah
Send_buf[6] = (int8_t)(dat); //datal
Send_buf[7] = 0xef; //ending byte
for(uint8_t i=0; i<8; i++)//
{
mySerial.write(Send_buf[i]) ;//send bit to serial mp3
Serial.print(Send_buf[i],HEX);//send bit to serial monitor in pc
}
Serial.println();
}
Now to go through the documentation for the Catalex MP3 board.
Something I have been meaning to experiment with for a while – a simple animation of some of the phone collages I have created for my Happy Half Hours. The first one is Interference Patterns (full Flickr set here).

A more robust prototype, testing out both square and rounded edges.
You must be logged in to post a comment.