Here’s a sneak preview of the We Are Here exhibition catalogue.
Images
We Are Here
New speaker to test
Love the packaging for this. One of these.
It’s definitely louder than the previous one, and with a better frequency response, but I think I will still need a pre-amp.
Fitting the electronics into the shapes
Arduino networked lamp test
Working through this tutorial currently, trying to understand how Processing can be used to network an Arduino and power the colour of a lamp from words featured in an XML feed (in this case my blog feed – replacing the word ‘love’ with ‘space’ and the word ‘peace’ with ‘rock’). This generates the colour #3C4C2C.

And after adding this post to the feed…
Note the slight colour change.
This is the circuit I used, from this website. The LED is a 4 pin one, which can generate any combination of RGB colour as light:

And the two versions of it that I built:


Here is the code used in Processing:
//Arduino Code for the Arduino Networked Lamp - Processing
#define SENSOR 0
#define R_LED 9
#define G_LED 10
#define B_LED 11
#define BUTTON 12
int val =0; //variable to store the value coming from the sensor
int btn = LOW;
int old_btn = LOW;
int state = 0;
char buffer[7];
int pointer = 0;
byte inByte = 0;
byte r = 0;
byte g = 0;
byte b = 0;
void setup() {
Serial.begin(9600); //open up serial port
pinMode(BUTTON, INPUT);
}
void loop() {
val = analogRead(SENSOR);
Serial.println(val);
if (Serial.available() >0) {
//read incoming byte
inByte = Serial.read();
if (inByte == '#') {
while (pointer < 6) {
buffer[pointer] = Serial.read();
pointer++;
}
//now need to decode 3 numbers of colors stored as hex numbers into 3 bytes
r = hex2dec(buffer[1]) +hex2dec(buffer[0])*16;
g = hex2dec(buffer[3]) +hex2dec(buffer[2])*16;
b = hex2dec(buffer[5]) +hex2dec(buffer[4])*16;
pointer = 0; //reset pointer
}
}
btn = digitalRead(BUTTON);
//check if there was a transition
if ((btn == HIGH) && (old_btn == LOW)) {
state = 1-state;
}
old_btn = btn; //val is now old,lets store it
if (state == 1) {
analogWrite(R_LED, r);
analogWrite(G_LED, g);
analogWrite(B_LED, b);
}
else {
analogWrite(R_LED, 0);
analogWrite(G_LED, 0);
analogWrite(B_LED, 0);
}
delay(100);
}
int hex2dec(byte c) {
if (c >= '0' && c<= '9') {
return c- '0';
} else if (c >='A' && c <= 'F') {
return c - 'A' + 10;
}
}
And the code in Arduino:
//Arduino Code for the Arduino Networked Lamp - Arduino
#define SENSOR 0
#define R_LED 9
#define G_LED 10
#define B_LED 11
#define BUTTON 12
int val =0; //variable to store the value coming from the sensor
int btn = LOW;
int old_btn = LOW;
int state = 0;
char buffer[7];
int pointer = 0;
byte inByte = 0;
byte r = 0;
byte g = 0;
byte b = 0;
void setup() {
Serial.begin(9600); //open up serial port
pinMode(BUTTON, INPUT);
}
void loop() {
val = analogRead(SENSOR);
Serial.println(val);
if (Serial.available() >0) {
//read incoming byte
inByte = Serial.read();
if (inByte == '#') {
while (pointer < 6) {
buffer[pointer] = Serial.read();
pointer++;
}
//now need to decode 3 numbers of colors stored as hex numbers into 3 bytes
r = hex2dec(buffer[1]) +hex2dec(buffer[0])*16;
g = hex2dec(buffer[3]) +hex2dec(buffer[2])*16;
b = hex2dec(buffer[5]) +hex2dec(buffer[4])*16;
pointer = 0; //reset pointer
}
}
btn = digitalRead(BUTTON);
//check if there was a transition
if ((btn == HIGH) && (old_btn == LOW)) {
state = 1-state;
}
old_btn = btn; //val is now old,lets store it
if (state == 1) {
analogWrite(R_LED, r);
analogWrite(G_LED, g);
analogWrite(B_LED, b);
}
else {
analogWrite(R_LED, 0);
analogWrite(G_LED, 0);
analogWrite(B_LED, 0);
}
delay(100);
}
int hex2dec(byte c) {
if (c >= '0' && c<= '9') {
return c- '0';
} else if (c >='A' && c <= 'F') {
return c - 'A' + 10;
}
}
This didn’t work the first time I ran it, so I had to specify the Arduino port that Processing should use and then…
Space Rock interaction eco-system (first draft)
Horniman Museum – objects and shapes
Spent a couple of hours at the Horniman Museum looking at shapes and unusual / ‘alien’ forms for the Space Rocks. Also interesting style of curation. See the gallery here.









You must be logged in to post a comment.