A rough guide to how all of the required electronics (XBee, Arduino Nano, speaker, sensor and – hopefully – a USB power bank) might fit into the four Space Rock shapes. All items drawn to scale.


The blog
Following on from discussion of presenting the objects in an environment that emphasises the sound over the visual, I revisited the snow goggles I had seen on one of my visits to the British Museum.
The Menil exhibit in Houston tries to re-create the limitless feeling of the Arctic where the horizon is hard to determine and it’s easy to get disoriented by the blinding snow. For centuries, different Inuit cultures have used “snow goggles” to help them see in such a bright white environment. The narrow slits constrict the wearer’s field of vision and reduce light to the optic nerve. Similar goggles are still used today.
https://www.menil.org/exhibitions/18-upside-down-arctic-realities
“A piezo creates a varying voltage when you squeeze it. [We’ll] use it as a sensor by measuring the voltage the piezo produces across a 1 megaOhm resistor…Notice it has a very fast response, especially a sharp attack and decay when it’s knocked.”
This first test was changing the frequency as the piezo was scraped and touched.
And the audio version:
Piezo sample trigger (& speed)
Piezo sample scrub
And finally an example of an external speaker circuit. Will need to work on the output level for this.
Some sketchbook work exploring how the objects could work using magnetic levitation.
Working through this tutorial currently, trying to understand how Processing can be used to network an Arduino and power the colour of a lamp from words featured in an XML feed (in this case my blog feed – replacing the word ‘love’ with ‘space’ and the word ‘peace’ with ‘rock’). This generates the colour #3C4C2C.

And after adding this post to the feed…
Note the slight colour change.
This is the circuit I used, from this website. The LED is a 4 pin one, which can generate any combination of RGB colour as light:

And the two versions of it that I built:


Here is the code used in Processing:
//Arduino Code for the Arduino Networked Lamp - Processing
#define SENSOR 0
#define R_LED 9
#define G_LED 10
#define B_LED 11
#define BUTTON 12
int val =0; //variable to store the value coming from the sensor
int btn = LOW;
int old_btn = LOW;
int state = 0;
char buffer[7];
int pointer = 0;
byte inByte = 0;
byte r = 0;
byte g = 0;
byte b = 0;
void setup() {
Serial.begin(9600); //open up serial port
pinMode(BUTTON, INPUT);
}
void loop() {
val = analogRead(SENSOR);
Serial.println(val);
if (Serial.available() >0) {
//read incoming byte
inByte = Serial.read();
if (inByte == '#') {
while (pointer < 6) {
buffer[pointer] = Serial.read();
pointer++;
}
//now need to decode 3 numbers of colors stored as hex numbers into 3 bytes
r = hex2dec(buffer[1]) +hex2dec(buffer[0])*16;
g = hex2dec(buffer[3]) +hex2dec(buffer[2])*16;
b = hex2dec(buffer[5]) +hex2dec(buffer[4])*16;
pointer = 0; //reset pointer
}
}
btn = digitalRead(BUTTON);
//check if there was a transition
if ((btn == HIGH) && (old_btn == LOW)) {
state = 1-state;
}
old_btn = btn; //val is now old,lets store it
if (state == 1) {
analogWrite(R_LED, r);
analogWrite(G_LED, g);
analogWrite(B_LED, b);
}
else {
analogWrite(R_LED, 0);
analogWrite(G_LED, 0);
analogWrite(B_LED, 0);
}
delay(100);
}
int hex2dec(byte c) {
if (c >= '0' && c<= '9') {
return c- '0';
} else if (c >='A' && c <= 'F') {
return c - 'A' + 10;
}
}
And the code in Arduino:
//Arduino Code for the Arduino Networked Lamp - Arduino
#define SENSOR 0
#define R_LED 9
#define G_LED 10
#define B_LED 11
#define BUTTON 12
int val =0; //variable to store the value coming from the sensor
int btn = LOW;
int old_btn = LOW;
int state = 0;
char buffer[7];
int pointer = 0;
byte inByte = 0;
byte r = 0;
byte g = 0;
byte b = 0;
void setup() {
Serial.begin(9600); //open up serial port
pinMode(BUTTON, INPUT);
}
void loop() {
val = analogRead(SENSOR);
Serial.println(val);
if (Serial.available() >0) {
//read incoming byte
inByte = Serial.read();
if (inByte == '#') {
while (pointer < 6) {
buffer[pointer] = Serial.read();
pointer++;
}
//now need to decode 3 numbers of colors stored as hex numbers into 3 bytes
r = hex2dec(buffer[1]) +hex2dec(buffer[0])*16;
g = hex2dec(buffer[3]) +hex2dec(buffer[2])*16;
b = hex2dec(buffer[5]) +hex2dec(buffer[4])*16;
pointer = 0; //reset pointer
}
}
btn = digitalRead(BUTTON);
//check if there was a transition
if ((btn == HIGH) && (old_btn == LOW)) {
state = 1-state;
}
old_btn = btn; //val is now old,lets store it
if (state == 1) {
analogWrite(R_LED, r);
analogWrite(G_LED, g);
analogWrite(B_LED, b);
}
else {
analogWrite(R_LED, 0);
analogWrite(G_LED, 0);
analogWrite(B_LED, 0);
}
delay(100);
}
int hex2dec(byte c) {
if (c >= '0' && c<= '9') {
return c- '0';
} else if (c >='A' && c <= 'F') {
return c - 'A' + 10;
}
}
This didn’t work the first time I ran it, so I had to specify the Arduino port that Processing should use and then…
The latest 3D printed prototypes for the Space Rock shapes.
Plus a video of the shells glowing, courtesy of Arduino.
Looking at some shapes that tessellate for the Space Rock 3D models.
Some low resolution 3D prints. Getting used to the process, investigating how to add the electronics for audio and interaction and also working out the most ergonomic size for the final objects. In this case, bigger is definitely better.
An evening spent in the Mesopotamian & Egyptian rooms at the British Museum. Full flickr set of photos here.
Some sketches for possible installation of Space Rock objects.
You must be logged in to post a comment.