3D sketches for outer space artefacts

Some screenshots of ideas for developing an ‘alien’ aesthetic for the outer space artefacts.

What goes around, comes around – PG02, Cycle 3

What goes around, comes around is a piece of work about the time capsule that was returned to Earth by ‘advanced space-faring civilizations’,  in response to the original Voyager record and images. This ‘message in a bottle’ from an extraterrestrial life form has been recently delivered via Oumuamua. Who sent it? And why?

Or is it an elaborate hoax by someone on Earth to perplex the current inhabitants? The aim is to find out more…


Current research includes:

I Am Sensor – Godzuino

A track created using the audio signals from Arduino, via four over-sized sensors: Twitch, Flexilla, Bütton and Anomomehelmet.

I Am Sensor artwork (Photo: Alexa Pollmann, typography & logo: Kat Hornstein)
I Am Sensor artwork (Photo: Alexa Pollmann, typography & logo: Kat Hornstein)

I Am Sensor – Twitch (tilt switch) code and circuit

The code and circuit for the Arduino-powered giant tilt switch was adapted from this page – http://starter-kit.nettigo.eu/2010/tilt-sensor/

Starting circuit for giant tilt switch
Starting circuit for giant tilt switch
Circuit for giant tilt switch
Circuit for giant tilt switch
/// Defining a pin for the tilt sensor
#define SENSOR_PIN 2
// Defining a pin for the LED diode
#define LED_PIN 13
// Defining a pin for the piezo
#define PIEZO_PIN 3
// Defining sensitivity time [ms]
#define SENSOR_TIME 100
// Defining alarm duration time [ms] (5000 ms = 5 s)
#define ALARM_TIME 10000

// variable storing sensor's switching time
unsigned long sensor_time;
// variable storing alarm duration
unsigned long alarm_time;
// variable storing pitch change time
unsigned long signal_time = 0;
// variable storing the pitch value
// 0 - no sound
// 1 - first tone
// > 1 - second tone
byte sound_tone = 0;

// alarm siren function
void alarm_signal()
{
  if (sound_tone != 0) // checking if the siren should be turned on
  {
    if (millis() - signal_time > 750) // checking tone duration
    {
      signal_time = millis(); // storing the time when the tone was turned on
      sound_tone = ~sound_tone; // turning on the second tone
    }

    if (sound_tone == 1) // first tone
    {
      tone(PIEZO_PIN, 300);
    }
    else // second tone
    {
      tone(PIEZO_PIN, 200, 100);
      delay(1000);
      tone(PIEZO_PIN, 400, 100);
      delay(1000);
    }
  }
  else
  {
    noTone(PIEZO_PIN); // Sound off
  }
}

// Function invoked when the alarm is off
void alarm_on()
{
  alarm_time = millis(); // storing the time when the tone was turned on
  digitalWrite(LED_PIN, HIGH); // LED on
  sound_tone = 1; // Turning alarm siren on
}

// Function invoked when the alarm is off
void alarm_off()
{
  if (millis() - alarm_time > ALARM_TIME) // checking alarm duration
  {
    digitalWrite(LED_PIN, LOW); // LED off
    sound_tone = 0; // Turning alarm siren off
  }
}

// function checking sensor's state
void check_sensor()
{
  // checking sensor's state
  if (digitalRead(SENSOR_PIN) == HIGH)
  {
    // Action if off

    if (sensor_time == 0) // checking if the state was changed
    {
      sensor_time = millis(); // storing sensor's activation time
    }
    // Condition, if sensor's state lasts for a specified time
    else if (millis() - sensor_time > SENSOR_TIME)
    {
      alarm_on();
    }
  }
  else
  {
    // Action if off
    sensor_time = 0;
    alarm_off();
  }
}

void setup()
{
  // Setting the sensor's pin as input
  pinMode(SENSOR_PIN, INPUT);
  // Turning internal Pull Up resistor on
  digitalWrite(SENSOR_PIN, HIGH);
  pinMode(LED_PIN, OUTPUT);
}

void loop()
{
  check_sensor();
  alarm_signal();
}

Second prototype for over-sized Arduino-powered tilt switch

Second prototype for over-sized Arduino-powered tilt switch - clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch – clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch - clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch – clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch - clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch – clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch - clear acrylic tube
Second prototype for over-sized Arduino-powered tilt switch – clear acrylic tube