I’d love to exhibit the Space Rocks in one of these. Back to the Futuro: the spaceship house that landed in Yorkshire.
The blog
I’d love to exhibit the Space Rocks in one of these. Back to the Futuro: the spaceship house that landed in Yorkshire.
The final 3D printed Space Rocks, (almost) ready for painting.
Working on the circuitry for the inside of the Space Rocks. With lots of help from Sitraka Rakotoniaina, we managed to get the code to work using a Nano I/O shield to connect the XBee and the Nano microcontroller. With a little help from a soldering iron and a wire from the RSSI pin (pin 6). Now looking forward to experimenting with this on all 4 circuits.
Here’s the current code, which maps the RSSI signal (essentially the distance between each Space Rock) from the XBees to a value that can effect the Mozzi synthesiser within the code.
/* ~ Simple Arduino - xBee Receiver sketch ~ Read an PWM value from Arduino Transmitter to fade an LED The receiving message starts with '<' and closes with '>' symbol. Dev: Michalis Vasilakis // Date:2/3/2016 // Info: www.ardumotive.com // Licence: CC BY-NC-SA */ #include <MozziGuts.h> #include <Oscil.h> // oscillator #include <tables/cos2048_int8.h> // table for Oscils to play #include <AutoMap.h> // maps unpredictable inputs to a range // desired carrier frequency max and min, for AutoMap const int MIN_CARRIER_FREQ = 22; const int MAX_CARRIER_FREQ = 440; // desired intensity max and min, for AutoMap, note they're inverted for reverse dynamics const int MIN_INTENSITY = 700; const int MAX_INTENSITY = 10; AutoMap kMapCarrierFreq(0,1023,MIN_CARRIER_FREQ,MAX_CARRIER_FREQ); AutoMap kMapIntensity(0,1023,MIN_INTENSITY,MAX_INTENSITY); const int KNOB_PIN = 0; // set the input for the knob to analog pin 0 const int LDR_PIN = 1; // set the input for the LDR to analog pin 1 Oscil<COS2048_NUM_CELLS, AUDIO_RATE> aCarrier(COS2048_DATA); Oscil<COS2048_NUM_CELLS, AUDIO_RATE> aModulator(COS2048_DATA); int mod_ratio = 3; // harmonics long fm_intensity; // carries control info from updateControl() to updateAudio() //Constants const int ledPin = 3; //Led to Arduino pin 3 (PWM) //Variables: int ff ; //Value from pot int pbPin = 7; //Variables bool started= false;//True: Message is strated bool ended = false;//True: Message is finished char incomingByte ; //Variable to store the incoming byte char msg[3]; //Message - array from 0 to 2 (3 values - PWM - e.g. 240) byte index; //Index of array int rssiDur = 0; int rssiMapped =0; bool calib = false; bool calib_top = false; int base_value= 0; int top_value=0; void setup() { //Start the serial communication Serial.begin(9600); //Baud rate must be the same as is on xBee module pinMode(ledPin, OUTPUT); pinMode(6, OUTPUT); calib = true; calib_top = true; startMozzi(); // :)) pinMode(pbPin, INPUT_PULLUP); } void updateControl(){ // read the knob //int knob_value = mozziAnalogRead(KNOB_PIN); // value is 0-1023 rssiDur = pulseIn(5, LOW, 200); rssiMapped = map(rssiDur, 10, 40, 0, 1023); Serial.print("raw RSSI : "); Serial.println(rssiDur); Serial.print("RSSI mapped : "); Serial.println(rssiMapped); delay(100); // map the knob to carrier frequency int carrier_freq = kMapCarrierFreq(rssiMapped); //calculate the modulation frequency to stay in ratio int mod_freq = carrier_freq * mod_ratio; // set the FM oscillator frequencies to the calculated values aCarrier.setFreq(carrier_freq); aModulator.setFreq(mod_freq); // read the light dependent resistor on the Analog input pin int light_level= mozziAnalogRead(LDR_PIN); // value is 0-1023 fm_intensity = kMapIntensity(light_level); } int updateAudio(){ long modulation = fm_intensity * aModulator.next(); return aCarrier.phMod(modulation); // phMod does the FM } void loop() { //delay(100); if(rssiDur != 0){ digitalWrite(6, HIGH); }else{ digitalWrite(6,LOW); } audioHook(); //Serial.println(digitalRead(pbPin)); //Read the analog value from pot and store it to "value" variable ff = digitalRead(pbPin);//analogRead(A0); //Map the analog value to pwm value //value = map (value, 0, 1023, 0, 255); //Send the message: Serial.print('<'); //Starting symbol Serial.print(ff);//Value from 0 to 255 Serial.println('>');//Ending symbol /*while (Serial.available()>0){ //Read the incoming byte incomingByte = Serial.read(); //Start the message when the '<' symbol is received if(incomingByte == '<') { started = true; index = 0; msg[index] = '\0'; // Throw away any incomplete packet } //End the message when the '>' symbol is received else if(incomingByte == '>') { ended = true; break; // Done reading - exit from while loop! } //Read the message! else { if(index < 4) // Make sure there is room { msg[index] = incomingByte; // Add char to array index++; msg[index] = '\0'; // Add NULL to end } } } if(started && ended) { int value = atoi(msg); //analogWrite(ledPin, value); Serial.println(value); //Only for debugging if(calib_top){ if(value == 0){ top_value = rssiMapped; Serial.println(top_value); calib_top = false; } } index = 0; msg[index] = '\0'; started = false; ended = false; }*/ }
Idea for the finish for the Space Rocks – Pearl finish.
The Space Rock shapes being CNC milled in PU foam for slush cast moulds.
…is Raymond Scott’s Three Willow Park: Electronic Music from Inner Space, 1961-1971.
Trying to keep track of the small things.
Have finally cracked getting my own samples into Mozzi. The sound clips need to be VERY short (around 0.5 seconds) or they are too big for the Nano. I also tried mono to see if that saved space, but then there was no sound at all. I really raised the volume of this sample and the clipping isn’t too noticeable compared to the previously-encoded version , as it clips because of the processing anyway.
Here’s the code:
/* Example of playing a sampled sound, using Mozzi sonification library. Demonstrates one-shot samples scheduled with EventDelay. Circuit: Audio output on digital pin 9 on a Uno or similar, or DAC/A14 on Teensy 3.1, or check the README or http://sensorium.github.com/Mozzi/ Mozzi help/discussion/announcements: https://groups.google.com/forum/#!forum/mozzi-users Tim Barrass 2012, CC by-nc-sa. */ #include <MozziGuts.h> #include <Sample.h> // Sample template #include <samples/alienwave.h> #include <EventDelay.h> #define CONTROL_RATE 64 // use: Sample <table_size, update_rate> SampleName (wavetable) Sample <alienwave_NUM_CELLS, AUDIO_RATE> aSample(alienwave_DATA); // for scheduling sample start EventDelay kTriggerDelay; void setup(){ startMozzi(CONTROL_RATE); aSample.setFreq((float) alienwave_SAMPLERATE / (float) alienwave_NUM_CELLS); // play at the speed it was recorded kTriggerDelay.set(1500); // 1500 msec countdown, within resolution of CONTROL_RATE } void updateControl(){ if(kTriggerDelay.ready()){ aSample.start(); kTriggerDelay.start(); } } int updateAudio(){ return (int) aSample.next(); } void loop(){ audioHook(); }
With thanks to Tim Barass and his very helpful forum for help getting this working.
You must be logged in to post a comment.