Updated Arduino random play MP3s

With excellent assistance from the Arduino forum, I now have a working version of the circuit to play a random MP3 file each time the distance sensor is triggered. It doesn’t play a few of the files when they are triggered, but this has been tested elsewhere and the code works, so I need to investigate the files themselves, it seems.

And here’s the code used.

#include <SoftwareSerial.h>

#define ARDUINO_RX 5  //should connect to TX of the Serial MP3 Player module
#define ARDUINO_TX 6  //connect to RX of the module

#define trigPin 13  //for the distance module
#define echoPin 12

SoftwareSerial mySerial(ARDUINO_RX, ARDUINO_TX);//init the serial protocol, tell to myserial wich pins are TX and RX

////////////////////////////////////////////////////////////////////////////////////
//all the commands needed in the datasheet(http://geekmatic.in.ua/pdf/Catalex_MP3_board.pdf)
uint8_t Send_buf[8] = {0} ;//The MP3 player undestands orders in a 8 int string
//0X7E FF 06 command 00 00 00 EF;(if command =01 next song order)
#define NEXT_SONG 0X01
#define PREV_SONG 0X02

#define CMD_PLAY_W_INDEX 0X03 //DATA IS REQUIRED (number of song)

#define VOLUME_UP_ONE 0X04
#define VOLUME_DOWN_ONE 0X05
#define CMD_SET_VOLUME 0X06//DATA IS REQUIRED (number of volume from 0 up to 30(0x1E))
#define SET_DAC 0X17
#define CMD_PLAY_WITHVOLUME 0X22 //data is needed  0x7E 06 22 00 xx yy EF;(xx volume)(yy number of song)

#define CMD_SEL_DEV 0X09 //SELECT STORAGE DEVICE, DATA IS REQUIRED
#define DEV_TF 0X02 //HELLO,IM THE DATA REQUIRED

#define SLEEP_MODE_START 0X0A
#define SLEEP_MODE_WAKEUP 0X0B

#define CMD_RESET 0X0C//CHIP RESET
#define CMD_PLAY 0X0D //RESUME PLAYBACK
#define CMD_PAUSE 0X0E //PLAYBACK IS PAUSED

#define CMD_PLAY_WITHFOLDER 0X0F//DATA IS NEEDED, 0x7E 06 0F 00 01 02 EF;(play the song with the directory \01\002xxxxxx.mp3

#define STOP_PLAY 0X16

#define PLAY_FOLDER 0X17// data is needed 0x7E 06 17 00 01 XX EF;(play the 01 folder)(value xx we dont care)

#define SET_CYCLEPLAY 0X19//data is needed 00 start; 01 close

#define SET_DAC 0X17//data is needed 00 start DAC OUTPUT;01 DAC no output
////////////////////////////////////////////////////////////////////////////////////

void setup() {
  Serial.begin(9600);  //Start our Serial coms for serial monitor in our pc
  mySerial.begin(9600);  //Start our Serial coms for THE MP3
  delay(500);  //Wait chip initialization is complete
  sendCommand(CMD_SEL_DEV, DEV_TF);  //select the TF card
  delay(200);  //wait for 200ms
  pinMode(trigPin, OUTPUT);
  pinMode(echoPin, INPUT);
  randomSeed(analogRead(A0));
}

void loop() {
  if (measureDistance(trigPin, echoPin) < 10) {
    int randTrackNo;
    randTrackNo = random(1, 9);
    sendCommand(0x03, randTrackNo);
    Serial.print("Playing track:");
    Serial.println(randTrackNo);
    delay(1000);  //wait to avoid errors
  }
  delay(300);
}

void sendCommand(int8_t command, int16_t dat) {
  delay(20);
  Send_buf[0] = 0x7e; //starting byte
  Send_buf[1] = 0xff; //version
  Send_buf[2] = 0x06; //the number of bytes of the command without starting byte and ending byte
  Send_buf[3] = command; //
  Send_buf[4] = 0x00;  //0x00 = no feedback, 0x01 = feedback
  Send_buf[5] = (int8_t)(dat >> 8);  //datah
  Send_buf[6] = (int8_t)(dat);  //datal
  Send_buf[7] = 0xef;  //ending byte
  for (uint8_t i = 0; i < 8; i++) {
    mySerial.write(Send_buf[i]) ;  //send bit to serial mp3
    Serial.print(Send_buf[i], HEX);  //send bit to serial monitor in pc
    Serial.print(" ");
  }
  Serial.println();
}

long measureDistance(int trigger, int echo) {
  long duration, distance;

  digitalWrite(trigger, LOW);  //PULSE ___|---|___
  delayMicroseconds(2);
  digitalWrite(trigger, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigger, LOW);

  duration = pulseIn(echo, HIGH);
  distance = (duration / 2) / 29.1;
  Serial.print("distance: ");
  Serial.println(distance);
  return distance;
}

Arduino adventures: triggering MP3 files with distance sensor

Finally got the circuit built to be able to read the distance sensor and the MP3 board, so now I can trigger a selected MP3 to play when something passes the sensor. What I built previously was overly-complicated and was most likely shorting out.

The videos show the sensor working from 1ocm distance, but this is easy to vary. They also show the sound looping if the object sensed stays in range, and also two separate pieces of audio being triggered. This was changed in the code before being uploaded. The code used is below.

Next to make it play a random one of the MP3 files each time the sensor is triggered!

//code rearranged by Javier Muñoz 10/11/2016 ask me at javimusama@hotmail.com
#include <SoftwareSerial.h>

#define ARDUINO_RX 5//should connect to TX of the Serial MP3 Player module
#define ARDUINO_TX 6//connect to RX of the module

#define trigPin 13//for the distance module
#define echoPin 12


SoftwareSerial mySerial(ARDUINO_RX, ARDUINO_TX);//init the serial protocol, tell to myserial wich pins are TX and RX

////////////////////////////////////////////////////////////////////////////////////
//all the commands needed in the datasheet(http://geekmatic.in.ua/pdf/Catalex_MP3_board.pdf)
static int8_t Send_buf[8] = {0} ;//The MP3 player undestands orders in a 8 int string
                                 //0X7E FF 06 command 00 00 00 EF;(if command =01 next song order) 
#define NEXT_SONG 0X01 
#define PREV_SONG 0X02 

#define CMD_PLAY_W_INDEX 0X03 //DATA IS REQUIRED (number of song)

#define VOLUME_UP_ONE 0X04
#define VOLUME_DOWN_ONE 0X05
#define CMD_SET_VOLUME 0X06//DATA IS REQUIRED (number of volume from 0 up to 30(0x1E))
#define SET_DAC 0X17
#define CMD_PLAY_WITHVOLUME 0X22 //data is needed  0x7E 06 22 00 xx yy EF;(xx volume)(yy number of song)

#define CMD_SEL_DEV 0X09 //SELECT STORAGE DEVICE, DATA IS REQUIRED
                #define DEV_TF 0X02 //HELLO,IM THE DATA REQUIRED
                
#define SLEEP_MODE_START 0X0A
#define SLEEP_MODE_WAKEUP 0X0B

#define CMD_RESET 0X0C//CHIP RESET
#define CMD_PLAY 0X0D //RESUME PLAYBACK
#define CMD_PAUSE 0X0E //PLAYBACK IS PAUSED

#define CMD_PLAY_WITHFOLDER 0X0F//DATA IS NEEDED, 0x7E 06 0F 00 01 02 EF;(play the song with the directory \01\002xxxxxx.mp3

#define STOP_PLAY 0X16

#define PLAY_FOLDER 0X17// data is needed 0x7E 06 17 00 01 XX EF;(play the 01 folder)(value xx we dont care)

#define SET_CYCLEPLAY 0X19//data is needed 00 start; 01 close

#define SET_DAC 0X17//data is needed 00 start DAC OUTPUT;01 DAC no output
////////////////////////////////////////////////////////////////////////////////////


void setup()
{
  Serial.begin(9600);//Start our Serial coms for serial monitor in our pc
mySerial.begin(9600);//Start our Serial coms for THE MP3
delay(500);//Wait chip initialization is complete
   sendCommand(CMD_SEL_DEV, DEV_TF);//select the TF card  
delay(200);//wait for 200ms
pinMode(trigPin, OUTPUT);
pinMode(echoPin, INPUT);

}

void loop()
{
  if(measureDistance(trigPin,echoPin)<50){
sendCommand(CMD_PLAY_WITHFOLDER, 0X0203);//play the third song of the second folder
delay(1000);//wait to avoid errors
}
delay(300);
}

void sendCommand(int8_t command, int16_t dat)
{
 delay(20);
 Send_buf[0] = 0x7e; //starting byte
 Send_buf[1] = 0xff; //version
 Send_buf[2] = 0x06; //the number of bytes of the command without starting byte and ending byte
 Send_buf[3] = command; //
 Send_buf[4] = 0x00;//0x00 = no feedback, 0x01 = feedback
 Send_buf[5] = (int8_t)(dat >> 8);//datah
 Send_buf[6] = (int8_t)(dat); //datal
 Send_buf[7] = 0xef; //ending byte
 for(uint8_t i=0; i<8; i++)//
 {
   mySerial.write(Send_buf[i]) ;//send bit to serial mp3
   Serial.print(Send_buf[i],HEX);//send bit to serial monitor in pc
 }
 Serial.println();
}

long measureDistance(int trigger,int echo){
   long duration, distance;
  
  digitalWrite(trigger, LOW);  //PULSE ___|---|___
  delayMicroseconds(2); 
  digitalWrite(trigger, HIGH);
  delayMicroseconds(10); 
  digitalWrite(trigger, LOW);
  
  duration = pulseIn(echo, HIGH);
  distance = (duration/2) / 29.1;
   Serial.println("distance:");
   Serial.println(distance);
  return distance;

}

MP3 played from Arduino

Finally at the stage where I can play a good quality sounding MP3 file through Arduino. It doesn’t sound so ‘good’ here as it is routed back through the laptop and Audacity via a crackly audio interface connection, but it is quite clear on headphones. And it’s now ready for me to start triggering these MP3 files via various sensors.

Here’s the code used:

//code rearranged by Javier Muñoz 10/11/2016 ask me at javimusama@hotmail.com
#include <SoftwareSerial.h>

#define ARDUINO_RX 5//should connect to TX of the Serial MP3 Player module
#define ARDUINO_TX 6//connect to RX of the module
SoftwareSerial mySerial(ARDUINO_RX, ARDUINO_TX);//init the serial protocol, tell to myserial wich pins are TX and RX

////////////////////////////////////////////////////////////////////////////////////
//all the commands needed in the datasheet(http://geekmatic.in.ua/pdf/Catalex_MP3_board.pdf)
static int8_t Send_buf[8] = {0} ;//The MP3 player undestands orders in a 8 int string
                                 //0X7E FF 06 command 00 00 00 EF;(if command =01 next song order) 
#define NEXT_SONG 0X01 
#define PREV_SONG 0X02 

#define CMD_PLAY_W_INDEX 0X03 //DATA IS REQUIRED (number of song)

#define VOLUME_UP_ONE 0X04
#define VOLUME_DOWN_ONE 0X05
#define CMD_SET_VOLUME 0X06//DATA IS REQUIRED (number of volume from 0 up to 30(0x1E))
#define SET_DAC 0X17
#define CMD_PLAY_WITHVOLUME 0X22 //data is needed  0x7E 06 22 00 xx yy EF;(xx volume)(yy number of song)

#define CMD_SEL_DEV 0X09 //SELECT STORAGE DEVICE, DATA IS REQUIRED
                #define DEV_TF 0X02 //HELLO,IM THE DATA REQUIRED
                
#define SLEEP_MODE_START 0X0A
#define SLEEP_MODE_WAKEUP 0X0B

#define CMD_RESET 0X0C//CHIP RESET
#define CMD_PLAY 0X0D //RESUME PLAYBACK
#define CMD_PAUSE 0X0E //PLAYBACK IS PAUSED

#define CMD_PLAY_WITHFOLDER 0X0F//DATA IS NEEDED, 0x7E 06 0F 00 01 02 EF;(play the song with the directory \01\002xxxxxx.mp3

#define STOP_PLAY 0X16

#define PLAY_FOLDER 0X17// data is needed 0x7E 06 17 00 01 XX EF;(play the 01 folder)(value xx we dont care)

#define SET_CYCLEPLAY 0X19//data is needed 00 start; 01 close

#define SET_DAC 0X17//data is needed 00 start DAC OUTPUT;01 DAC no output
////////////////////////////////////////////////////////////////////////////////////


void setup()
{
  Serial.begin(9600);//Start our Serial coms for serial monitor in our pc
mySerial.begin(9600);//Start our Serial coms for THE MP3
delay(500);//Wait chip initialization is complete
   sendCommand(CMD_SEL_DEV, DEV_TF);//select the TF card  
delay(200);//wait for 200ms

}
void loop()
{
sendCommand(CMD_PLAY_WITHVOLUME, 0X0F01);//play the first song with volume 15 class
delay(1000000);//the programm will send the play option each 100 seconds to the catalex chip
}

void sendCommand(int8_t command, int16_t dat)
{
 delay(20);
 Send_buf[0] = 0x7e; //starting byte
 Send_buf[1] = 0xff; //version
 Send_buf[2] = 0x06; //the number of bytes of the command without starting byte and ending byte
 Send_buf[3] = command; //
 Send_buf[4] = 0x00;//0x00 = no feedback, 0x01 = feedback
 Send_buf[5] = (int8_t)(dat >> 8);//datah
 Send_buf[6] = (int8_t)(dat); //datal
 Send_buf[7] = 0xef; //ending byte
 for(uint8_t i=0; i<8; i++)//
 {
   mySerial.write(Send_buf[i]) ;//send bit to serial mp3
   Serial.print(Send_buf[i],HEX);//send bit to serial monitor in pc
 }
 Serial.println();
}

Now to go through the documentation for the Catalex MP3 board.

Coding the Space Rock player with Arduino

Have had lots of fun and games trying to get the Arduino element of the player to work, so far.

Firstly, getting the newly-purchased SD card to read was relatively straightforward. Once I worked out that I could transfer the files through my camera (as I don’t have an SD card reader other than the one I had just bought to attach to the Arduino), testing to see if it was connected and reading the files on there worked okay. Once I had reformatted the card for FAT32, at least. There is still an issue with some of the files having names too long for the DOS 8.3 naming convention, but I will rename these later.

Testing the SD card reader
SD card reader working

Next, I bought the additional components (amplifier chip and capacitors) for, and built, this circuit:

Simple Audio player schematic
Simple Audio player schematic
Simple Audio player amplifier circuit

Unfortunately, not realising there was a difference between the Arduino DUE board, which this circuit was designed for, and the Arduino (Elegoo) UNO I have, took me off on the wrong track somewhat and cost me a fair bit of time. Essentially, the DUE uses the Audio.h library, which needs the DAC port. A port my UNO sadly doesn’t have.

So, next, lots of Googling, trying to find a simpler circuit and code that uses the TMRpcm library instead. For a while, every bit of code I verified was giving me errors similar to this one (I tried a few!):

So then I decided to try the other computer, and the same lines of code all worked fine.

Next, to build the circuit. I tried to build this:

Simple Audio player with two buttons.

But the wiring around the capacitors and amp chip lost me completely.

Then I started working with this code – https://maxoffsky.com/maxoffsky-blog/how-to-play-wav-audio-files-with-arduino-uno-and-microsd-card/ – and finally managed to play various of the .wav files on the card
(although the audio was so distorted it was sometimes hard to tell!).

But how to make the circuit, so that it wasn’t just plugged straight into the Arduino board? After a couple of false starts, I found and built this:

This meant I now had very distorted, but louder audio from the speaker.

Simple audio amp circuit for testing
Simple audio amp circuit for testing

So…next steps..?

  1. Build the more complex amplifier circuit above that works on the UNO, ideally with a potentiometer for volume control
  2. Find and write the code to play the .wavs whenever a tilt switch is activated, and turn off again when tilted back into place
  3. Find and write the code to make this happen randomly (ie play one of the eight .wav files at random) when the player is tilted forward (rather than the current keyboard entry in serial monitor)
  4. Last, but definitely not least, think about how the circuitry and power can fit inside the player shell

Watch this space.

Inspiration for the ‘Space Rock’ audio player

I want to make one of these. Imagining them as a limited edition for a band or artist, loaded with samples of their work, so the user can create their own soundscapes. Could be a version using the Voyager Sounds collection?

And also a nod to the interactive tilt radio by Luka Or, whose shape initially inspired the ‘Space Rock’.
https://www.designboom.com/design/tilt/